4 Follow the instructions displayed on screen. Disable any anti-virus programs.ġ0 3 Place the Setup Sof tware & User ’s Guide CD-ROM in the CD-ROM drive. If any applications automatically run, quit th em. 2 T urn on the computer and st art Windows.
Loading A4 (Letter) Size Plai n Paper in the Sheet Feeder 1 Pull out the Paper Support and Paper Output T ray completely as shown.ĩ 5 Installing the Printer Driv er Inst alling the Printe r Driver – Windows 1 Ensure that the printer and computer are turned of f. When performing the print head alignment, you need to load paper in the Sheet Feeder.
Only install the ink tanks in the positio ns specified by the labels.Ĩ 4 Loading Paper This section describes how to load paper in the Sheet Feeder.6 Put back the Inner Cover and close the T op Cover. Check the labels to make sure that each tank is in the correct position. Be sure to remove the clear film from the i nk tank in the exact order as shown in step 2.ħ 5 Use the same procedure to inst all the other ink tanks in to their appropriate slots.Do not drop or shake ink tanks as this may cause the ink to leak out and st ain your clothe s and hands.For safety reasons, store ink tanks out of the reach of small children.Do not touch the Print Head Nozzles or electrical c ontacts.Do not touch the lever once the Print Head has been installed. 8 Lock the Print Head into place by lowering the lever. Do not place heavy objects on the power cord.ĥ 6 Remove the protective cap from the Print Head. Never damage, modify, stretch, or excessively bend or twist the power cord.Never attempt to plug the power cord into the power outlet or unplug the power cord when your hands are wet.Figure B shows the printer cable (parallel) connection (iP4000 only). 1 Ensure that the printer and the computer are turned of f. 2 Connecting t he Printer to t he Computer Either a USB cable or parallel printer cable is available for iP4000.ģ Follow the step s below to install th e printer driver correctly. 2 Remove the pa cking material and tape from the printer as shown. If anything is missing or is damaged, contact your Canon Servic e Represen tative.Ģ Setting Up 1 Pre paring the Print er 1 Place the printer on a flat surface. Check that all the following items are in the box. By connecting to an Exif Print-complia nt digital camera, the camera’ s imag e data at the time of shooting is used and optimized, yielding extremely high quality prints.ġ Preface Shipping Materials Thank you for purchasing a Canon Bubble Jet Printer. Exif Print is a standard for enhancing the comm unication between digital cam era s and printers. If the envelopes are placed in landscape orientation, they will not feed properly.Ĭheck5 Make sure media type and paper size settings match with loaded paper.Ĭheck6 Make sure that there are not any foreign objects in the rear tray.Quick S t art Guide T able of Contents Preface 1 Shipping Materials 1 Introduction 1 Setting Up 2 Preparing the Prin ter 2 Connecting the Printer to th e Computer 2 Installing the Print Head 4 Loading.Įxif Print This printer supports ExifPrint. Once you have prepared the envelopes, load them in portrait orientation.
See Loading Paper, and prepare the envelopes before printing. Align the paper stack against the right side of the rear tray and slide the paper guide so that it just touches the left edge of the stack.Ĭheck4 When loading envelopes, consider the following: When you load the paper, load the paper with the print side facing UP. In such cases, reduce the amount of paper you load at a time to less than half of the paper load limit.Īlways load the paper in portrait orientation, regardless of the printing orientation. However, paper may not feed correctly at the maximum capacity, depending on the type of paper or environmental conditions (very high or low temperature and humidity). When loading two or more sheets of paper, make sure the paper stack does not exceed the paper load limit. When loading two or more sheets of paper, align the edges of the sheets before loading the paper. Check2 When loading paper, consider the following.